Glitter Glamper Progress: Epoxy Resin Glitter Backsplash

Yesterday I finally started blogging about my process of turning my 1963 Shasta into THE Glitter Glamper! I shared some of the uglier work yesterday: removing a little rot, fixing a dent and sealing up holes. Today I thought I’d share one of the “prettier” projects: the glitter backsplash!

As I mentioned last time, the interior of this camper is so beautifully original that, while I need and want to transform it to scream “Glitter Glamper,” I still want to achieve this while preserving the original state underneath. I need to brighten it up overall so that I can get great lighting to work in, and also create an environment that feels unmistakably and unforgettably “Glitter Glamper” to my guests. Yes, this has created significantly more time and expense versus just painting over everything with white and coating it with glitter, however, I am enjoying the process so far and loving the results!

I knew that the area between the countertops and cabinets presented a great opportunity to inject some glitter, by way of a backsplash. I explored a few options, from glitter wallpaper to a gem mosaic and everything in between, but in my mind they all started with cut panels that could be put up and removed if I wanted to later. In order to achieve the ultimate in glittery-ness (yup, that’s a word I have full authority to create as a glitterologist, haha!), I decided to go with a poured resin and super chunky glitter. This would enable me to use big, sparkly glitter but still seal it up in a durable, wipe-able surface that can easily be kept clean without glitter constantly shedding!

I started by purchasing some pressed hardboard from Home Depot, and cut panels to fit above the counter, carefully measuring to make sure it fit around outlets, the window, etc. When going for a solid, uniform color coverage with glitter, just as I would paint the skin under one of my glitter “wannabeards” before applying the same color glitter, I want to lay down some paint as a background. This gives the illusion of full, opaque coverage of glitter, even if you may have spots here and there where glitter has fallen off or isn’t as thick. I went with a white base coat here, because I’m using silver glitter. A gray would work too, but my goal is brightness and silver reflects white as well, so it was perfect! Not only did the white paint give me a more even look, but it helps seal up the wood, so it took less glue and less resin in the end. I painted the back, front and edges of each piece and allowed them to dry. Then on to the fun part…

I bought a couple 1 lb jars of chunky glitter from the craft store. (Note: we do not EVER use metallic craft glitter on skin…only cosmetic grade glitter!) I laid each piece of wood on a large piece of tagboard that had been folded in the middle (or newspaper for the longer ones), and then coated the wood with Mod Podge. School glue would work too…but Mod Podge is already watered down glue, so it spreads farther and quicker, which was my goal. After a coating of Mod Podge, I then dumped plenty of glitter over the wet glue and allowed it to dry. Then I carefully lifted the panel and shook off the loose glitter, set it aside, folded the paper and funneled the extra back into the jar.

Pouring the Resin

Before pouring the resin, there is a bit of prep work to do. You have to prepare a very level surface to work on, as gravity will spread your resin out, and you want it to be an even thickness. I used my kitchen counter, and covered it with many layers of newspaper, to protect it if any resin spilled over. (For the next round I laid out painters’ plastic, which is better as it won’t soak up resin like newspaper!) Also, make sure that you have the ability to leave your pieces there for 24 hours to set, where it will remain stable, level, and free of floating particles of dust or whatever! Making dinner was tricky around this and made me a little nervous, but it worked out just fine.

Then, you have to create some sort of “fence” around whatever you are pouring resin onto, of course, to keep it from just pouring off the edge. I used painters tape and went around all edges, making sure to fold it under and rub it tightly against the underside of the wood to contain the resin while it was still liquid.

Here is what I used for my resin:

Whatever resin you use, make sure to carefully read and follow the directions! I got out some paper cups to pour each part into, and then a cool whip bowl to mix them together in. I also got out a couple plastic knives and a foam brush to help spread the resin. Different brands will have different amounts of time that the resin is work-abe, before it hardens. Pay attention to that, as you only have so much time to spread it before it sets up.

Pour out equal parts of resin into the paper cups to ensure you have an equal amount of both resin and hardener. Then, pour the two cups together in your larger container, and mix. Make sure to mix it well…epoxy resin is a chemical process that requires equal parts and thorough mixing! Once I had it well mixed, I slowly drizzled it over the glitter, trying to distribute it as evenly as I could. Then, I used the foam brush (and plastic knives for the tighter corners) to make sure that it was spread out and covering all of the glitter.

Get down low so you can catch a reflection in your resin. This will show you where you may need to add more, spread it out, etc. The act of mixing resin will undoubtedly fill it with lots of bubbles. When doing a smaller project, all you need to do is get down close and exhale over the surface, and you’ll see the bubbles rise and pop! For this I took a heat gun and ran it over all the surfaces. A hair dryer would probably also work, though a heat gun blows less and will disturb the surface less. The heat causes the bubbles to rise and pop. Be careful not to burn your project! With this particular project, air bubbles were virtually unnoticeable anyway because of all the light bouncing around inside from the glitter. However, removing them helps it to be smooth and strong.

There is one little ledge area above the fridge where I had a lip on the panels, to hold things in during transit. Since a couple inches of the back of my panels was visible here, I glued some fun fabric on that edge. When installing each panel, I first drilled pilot holes so as not to crack the resin when I screwed it in. Everything went up beautifully with minimal screws!

There were just a few edges that showed in the end, including this little ledge where I had the fabric backer, so I covered those with some bling-y trim and a glue gun.

Overall I LOVE how it turned out. Photos truly do NOT capture the amount of depth and sparkle in this! I love it so much, that I’m toying with the idea of an epoxy resin flooring as well. We shall see…that may be a project for spring! In the meantime, this turned out exactly as I had imagined, and consider it a big win in achieving my intense glittery-ness and remove-ability!

Thanks for stopping by…Stay tuned for more updates on the progress! 🙂

Published by Gretchen

Gretchen Fleener is an author, magazine editor, body painter, and entertainment agent based in Minnesota. She sells face & body art supplies via her online store Paintertainment.com, acts as an entertainer and agent at local events, publishes a body art magazine and teaches at workshops and conventions around the globe.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

%d bloggers like this: